My 1946 120 Resto project N77220

[6643]

Kazoo120 » Sat Jun 29, 2013 10:03 am

Visited Ken and Lorraine at Taildraggers a few weeks ago, what a great operation they have there. Saw a 140 that they have in-work that will be brought to Oshkosh Lorraine said, to demonstrate propping at the Red Barn. Will look forward to that. Worked with Lorraine to choose some materials and left the seats for her to reupholster. She believed that they were original, right down to the horse hair filling.

Also had the opportunity to visit Jeff Tourt over in Sandwich IL and to see his well prepared 140 there (See the June Calendar picture). Jeff has been very helpful primarily with questions I've had on paintwork, as he runs a very nice body shop operation over his way. It was a great visit.

Left these seats with Lorraine, she will also make front side panels for me.

dscn3014_330.jpg (145.74 KiB) Viewed 6846 times

[6643]

Kazoo120 » Sat Jun 29, 2013 10:09 am

Continued to re-assemble some items. I rebuilt the Gascolator and Primer, two easy tasks. Both were in great shape, just needed gaskets and O-rings etc..

Also installed the brake master cyl's.

John Davis local here in Kazoo, fixed me up with a set of rudder bar shields. Didn't have them originally, but it seems they would dress out the pedal area nicely, and keep some general dirt and stuf out of the well.

imag1245_140.jpg (58.32 KiB) Viewed 6846 times

Gascolator in place, and some of the wiring going back in.

imag1254_191.jpg (70.86 KiB) Viewed 6846 times

Brake Masters going in.

imag1216_379.jpg (63.57 KiB) Viewed 6846 times

[6643]

Kazoo120 » Sat Jun 29, 2013 10:13 am

Working on firewall covering. Lorraine at Taildragger fixed me up with some material and glue, and drew the basic pattern on the piece for me. I made a cardboard final pattern to mark my specific needed openings, and used scissors and carpet knife to final cut the firewall cover. Ready to glue in.

Using the cardboard pattern

imag1248_235.jpg (49.8 KiB) Viewed 6845 times

Ready to glue-in.

imag1249_454.jpg (75.51 KiB) Viewed 6845 times

[6643]

Kazoo120 » Sat Jun 29, 2013 10:19 am

A&P Ray removed the door glass pieces. .060" Lexan will be cut to replace them. And Helper Greg cleaned up the original Scott tail wheel, will get some new parts for it and rebuild.

Next step is the electrical wiring. We've drawn up a schematic and have an EE helping us to spec the wire, switches, CB's etc. Coming up soon.

Window glass removed

imag1250_110.jpg (77.21 KiB) Viewed 6845 times

Scott tail wheel cleaned up

imag1252_365.jpg (82.23 KiB) Viewed 6845 times

Coming Along

imag1255_132.jpg (80.85 KiB) Viewed 6845 times

[6643]

flyingdakota » Sat Jun 29, 2013 10:34 pm

Hey Kazoo120,
DON"T use Lexan! Use acrylic! Lexan is soft and hard to repair and very easy to scratch. Acrylic is harder, easier to polish and repair and in the event of a roll over you can break it to get out.
Trust me, I thought the same thing on the thought that Lexan (polycarbonate) would be better. Now i wish i would have listened to the ole' timers and put acrylic in.
Cheers!
Tim

Life is too short to sweat the small stuff!
NC2404V 1948 C-140 "The Arctic Tern"
http://arctictern-nc2404v.tumblr.com/
A&P IA as of 10/02/2009
http://www.mixasllc.com/
FB: https://www.facebook.com/MASat4S9

[6643]

Randy Thompson » Sat Jun 29, 2013 11:39 pm

Lexan also degrades when gas is spilled on it.

A&P IA. Holder of STC for O-200A's in 120, 140 & 140A's. Engine overhauls on C-85's ,C-85's with O-200 crankshaft, C-90's and O-200A's
State Rep for California

[6643]

Kazoo120 » Sun Jun 30, 2013 11:07 am

Acrylic sheet instead of Lexan, thanks for the tip, I will do that!

[6643]

Kazoo120 » Sun Jun 30, 2013 11:29 am

Disassembled the gauge panel yesterday. Someone made a pretty rough cutout to put a 7 O'Clock altimeter in, so will have to figure out a way to fix the appearance of that. Planning to add a rate of climb/descent gauge and a turn coordinator to what was originally installed by the factory. And replace all but the tach and compass with new I think. Wondering what gauges look most like the original..?

Gauges removed

imag1256_280.jpg (81.13 KiB) Viewed 6841 times

[6643]

Martin S. » Sun Jun 30, 2013 8:42 pm

I need to replace this section of my panel with a new one.

The old one is badly cut up.

Will you do this yourself?

Do you know anyone who does panel cutouts?

Martin S.
N76829
1946 140

[6643]

Kazoo120 » Mon Jul 01, 2013 9:32 am

Had the opportunity to fly over to Houghton Lake airport here in Michigan, for the Michigan chapter C120/140 fly-in there. We came in a 172 piloted by a co-worker friend, and another 172 that another co-worker owns joined us as well. 5 C120/140's came in and Dick Acker was there from the club.

It was a very nice get-together, and I took the opportunity to find out as much as I could about what guys have done with their planes. I won't be able to get to the National convention very unfortunately, because of schedule conflicts, so this was an opportunity to see some aircraft and members.

I was amazed to hear passing comment that there was still a perception around, that N77220 had been in poor condition and not worth the auction price, I hope that this thread shows how great a restoration project, and find, this bird has been. I'm thoroughly enjoying the process of bringing this classic plane, back to flightworthiness!

The flight line!

dscn3085_154.jpg (39.52 KiB) Viewed 6841 times

Dick Acker addressing the attendees.

dscn3084_113.jpg (200.69 KiB) Viewed 6841 times

The 172's we came in.

dscn3079_783.jpg (40.73 KiB) Viewed 6841 times

Takeoff to the west from Houghton Lake. Beautiful view. famous for its winter "Tip-up Town" festival.

dscn3098_180.jpg (148.35 KiB) Viewed 6841 times