STCs – 140A
The International Cessna 120-140 Association provides information for reference and historical purposes. They are not intended to be a substitute for official publications. It is the responsibility of the individual aircraft owner and their AP/AI to determine the applicability and/or legality of this information.
Supplemental Type Certificates – Cessna 140A
SA00072NY | Installation of a Sensenich model 72CK fixed-pitch metal propeller. | Issued | 02/25/1994 |
SA00081NY | Installation of Iceman Aviation Supplies Inc. Carburetor Ice Detector. | Amended | 12/07/1995 |
SA00165BO | Installation of Avidyne Corporation Datalink Coupler, part number 700-00015-000 per Avidyne Corporation Master Document List, Document No. AVACP-006 dtd 1/2/93 or later FAA-approved revisions. | Issued | 02/20/2003 |
SA00188AT | Installation of Appalachian Accessories carbon steel brake discs that have the melonite surface treatment, P/N AA-26A. | Reissued | 11/14/1994 |
SA00215NY | Installation of CAVU Model AM100 AVMIX engine fuel/air mixture setting system. | Amended | 08/14/1995 |
SA00432SE | Installation of EGT 701 series fuel flow instrument. | Amended | 04/19/2002 |
SA00780SE | Installation of the True Lock Safety Retention Axle Lock Nut System. (J3C Series; Army L-4, L-4A, L-4B; Navy NE-1; L-4H, L-4J; Navy NE-2) | Amended | 02/01/2001 |
SA00861SE | Installation of J.P. Instruments (JPI) fuel flow indicating system in accordance with JPI Installation Manual FS-450, Report No. 400, Revision -, dated August 16, 2000, or later FAA approved revision. | Issued | 12/18/2000 |
SA00897WI | Installation of Concorde Battery Corporation (VRSLA) Valve regulated sealed lead acid battery. | Issued | 08/11/2000 |
SA01312AT | Installation of Teledyne Continental Motors models C-85-12, C-85-12F, and C-85-14F engines which have STC SE01309AT installed. | Issued | 03/24/1997 |
SA01814CH | Replace Cessna S-43 fabric attachment clips with AD42ABSLF rivets | Issued | 04/18/2003 |
SA02033AT | Modification to install an air-oil separator to prevent oil from being aspirated from the engine breather line (47J series w stc’s SH4-235SW, SH4-826SW or SH479SW). | Amended | 05/22/2002 |
SA02072AK | Installation of hourmeter airspeed switch. | Amended | 11/14/1997 |
SA02168AK | Installation of hourmeter airspeed switch. For unpressurized aircraft only. Pressurized aircraft must have pressurization system deactivated. | Issued | 03/23/2001 |
SA02482AT | Installation of airplane weight restriction placard. | Issued | 04/02/2002 |
SA02520AT | Installation of M-20 Oil Separator, model 600-WP. | Issued | 05/30/2002 |
SA09470SC | Installation of Starter Indicator light system. | Issued | 06/18/2001 |
SA1-252 | Safety gear Model A. | Issued | 01/01/1960 |
SA1-259 | Wing covering of alclad panels. | Issued | Unknown |
SA10005SC | Installation of airflow register into baggage compartment cover and insert a screened vent into empennage inspection plate. | Amended | 09/09/2002 |
SA1005SC | Installation of airflow register into baggage compartment cover and insert a screened vent into empennage inspection plate. | Issued | 07/23/2002 |
SA10077SC | Installation of push-button starter system. | Issued | 01/13/2003 |
SA105GL | Install a pitot-static tube. | Issued | 01/16/1976 |
SA1177WE | WECO carburetor temperature monitor. | Issued | 01/01/1960 |
SA12WE | Installation of fiberglass wing tips. | Amended | 12/15/1998 |
SA1315WE | Installation of Tri-Star Corp. mixture monitor (exhaust gas temperature probe, gage, and selector). | Reissued | 10/10/1985 |
SA1351WE | Replace existing fabric on wings, fuselage, empennage, and/or control surfaces, with Ceconite101 material. (262A Series -12) | Amended | 08/19/1983 |
SA1371SW | Wing leading cuff, wing tips and upper surface flow fences. | Amended | 04/14/1983 |
SA1398SO | Remove drain plug AN-806-6 from fuel line drain in belly of aircraft and replace with drain valve MT-101-1. (See limitations) | Amended | 02/19/2003 |
SA13GL | Installation of Cleveland wheel No. 40-97A and brake No. 30-63A. (140A S/N 13400 AND UP) | Amended | 04/01/1981 |
SA1455NM | Installation of a flame proof auxiliary heater-dryer, Model12-1600. | Amended | 12/11/1985 |
SA1474SW | Installation of ‘MASA’ 1223000-7 and -8 wing tip. | Reissued | 09/05/1979 |
SA1525GL | Install retractable lifting handles, Model H. | Issued | 10/17/1990 |
SA1571NM | Installation of Jensen aircraft fuel valve plug No. 011-4. | Reissued | 01/29/1999 |
SA1643GL | Installation of V-type or Y-type shoulder harness. (182 SERIES EXCEPT R182 & TR182) | Amended | 08/31/1995 |
SA175WE | Conversion of aircraft for parachute jumping and aerial photography operations. | Issued | Unknown |
SA2096CE | Operation of airplane on unleaded automotive gasoline, 87 minimum antiknock index and leaded automotive gasoline, 88 minimum antiknock index (RON + MON)/2. Intermixing with aviation gasoline also approved. | Amended | 06/23/1992 |
SA2162NM | Installation of the Precise Flight stand-by vacuum system, Model SVS III. | Amended | 04/14/2000 |
SA2236SO | Replacement of Cleveland brake discs P/N 164-26 or 164-126 with Appalachian Accessories’ stainless steel brake discs P/N 75-27. | Issued | 01/21/1988 |
SA2666WE | Ceconite 102 material covering complete aircraft. (262A SERIES -12) | Amended | 08/19/1983 |
SA267SW | Continental O-200-A engine and a McCauley 1A100 MCM propeller. | Issued | Unknown |
SA268CE | Installation of tow hitch assembly. | Issued | Unknown |
SA2844CE | Installation of a plastic cap enclosure over the anti-collision strobe light system. | Issued | 07/29/1992 |
SA295WE | Mounting bracket fabrication. | Issued | 01/01/1960 |
SA3-114 | Instrument panel modification. | Issued | Unknown |
SA3-423 | Installation of CT-3000 tail ski on airplanes equipped with Scott 3200 or 3400 tail wheels. | Reissued | 02/16/1993 |
SA308EA | Installation of carburetor ice detection system 105AP in single and twin engine aircraft and single engine helicopters powered by Continental, Franklin, and Lycoming type engines equipped with Marvel-Schebler MA-2, MA-3, MA-4, MA-4-5, MA-6 and HA-6 series carburetors. (Normal,Utility and Acrobatic Category airplanes and helicopters equipped with engines and carburetors as described.) | Amended | 11/20/1978 |
SA3203SO | Replacement of Cleveland brake disks, P/N 164-26A and/or 164-126A, with Appalachian Accessories stainless steel brake disks P/N 75-27. | Reissued | 09/29/1995 |
SA323GL | Installation of fuel tank caps. | Issued | 07/16/1979 |
SA3300NM | Use of unleaded automobile gasoline, 87 minimum antiknock and 88 minimum antiknock index leaded automobile gasoline. | Issued | 11/05/1985 |
SA3501NM | Installation of a dorsal fin. (140A NOT INCLUDING LANDPLANES) | Issued | 05/30/1986 |
SA3815NM | Installation of BAS tail pull handle in the aft fuselage. | Amended | 06/09/1998 |
SA4-1200 | Delco-Remy generator 1101879 and regulator 1118384. | Issued | Unknown |
SA4-1210 | Installation of Eonnex cover on aircraft surfaces. | Reissued | 08/19/1980 |
SA4-1346 | Fiberglas covering of airplane surfaces. | Issued | Unknown |
SA4-174 | Glass cloth application over muslin to wings only. | Issued | Unknown |
SA4-341 | Recovering of wings with .02024ST alclad sheet. | Issued | 01/01/1960 |
SA4-360 | Recovering of wings with aluminum alloy sheet. | Issued | Unknown |
SA4-376 | Installation of a Lycoming O-235-C1 or O-235-C2C engine, in accordance with McKenzie Aircraft Repair Installation Instructions and Drawing No. L149-0600-244, Sheets 1 and 2, Revisions 1, 2, and 3, or later FAA approved revisions. Cowling is the same as that used on 1947 Model 140. Airplane Flight Manual Supplements are required with this installation. | Reissued and Amended | 03/01/2002 |
SA4-394 | Installation of George M. Adams DGA-2000 wheels and bodell Manufacturing Model BMI-252 brakes. | Amended | 01/15/1976 |
SA4-581 | Installation of a Lycoming O-290-D engine and Sensenich M76AM-2 or Sensenich CS3FM4 propeller, in accordance with McKenzie Aircraft Repair Installation Instructions and Supplemental Parts List dated June 28, 1958, and McKenzie Aircraft Repair Installation Instructions and Parts List dated September 10, 1955, and McKenzie Aircraft Repair Drawing L149-0600-244, Revision 4, dated June 23, 1958, Sheets 1 and 2, or later FAA approved revisions to all of the above. | Reissued and Amended | 03/01/2002 |
SA4-640 | Installation of a Lycoming O-290-D2 engine and Sensenich M74DM propeller, in accordance with McKenzie Aircraft Repair Installation Instructions dated October 30, 1958, (revised August 24, 1976), and McKenzie Aircraft Repair Drawing L149-0600-244, Sheets 1 and 2, Revisions 1, 2, and 3, or later FAA approved revisions. For seaplane configuration, the McCauley 1A175/GM-8240 propeller is required. | Reissued and Amended | 03/01/2002 |
SA4-674 | Eonite covering on wings. | Issued | Unknown |
SA4-79 | Recovering of wings with metal.020 aluminum 2024-T3 clad. | Issued | 01/01/1960 |
SA4-803 | Ceconite 101 covering of wings. | Issued | Unknown |
SA4-89 | Recovering of wings with metal .020 alclad 2024T3 aluminum alloy. | Issued | 01/01/1960 |
SA4-916 | Tricycle gear. | Issued | Unknown |
SA4005NM | Installation of Precise Pulselite control unit in landing/taxi system. (HP Jetstream Model 3101 AND SUPER 31) | Amended | 06/04/2001 |
SA489EA | Installation of ARP Inc. carburetor ice detection system Models 107AP (-12, -R-12, -24 and -R-24 series) in single and twin engine aircraft and single engine helicopters powered by Continental, Franklin, and Lycoming type engines equipped with Precision A ir-Motive (Facet or Marvel-Schebler) MA-2, MA-3, MA-3SPA,MA-4, MA-4-5, MA-4SPA, MA-5, MA-6, MA-6AA and HA-6 series carburetors. | Amended | 12/05/2002 |
SA5159NM | Installation of chip detector system. | Amended | 11/06/1992 |
SA547EA | Installation of Continental O-200-A engine and McCauley 1A100/MCM6952 or1A101/DCM6952 propeller. | Reissued | 10/28/2002 |
SA54CE | Covering of wings with .020-inch 24ST aluminum. | Issued | 06/05/1965 |
SA5581SW | Installation of ALCOR true-flow/ totalizer system. Requires STC SE5583SW which can be installed on aircraft equipped with Teledyne Continental engines IO-360, L/TSIO-360, TSIO-360, TIO-360, TSIO-470, GTSIO-520, L/TSIO-520, TSIO-520, IO-520, and IO-470. The approved model numbers listed may not be inclusive | Amended | 09/30/2002 |
SA5656NM | Installation of burglar alarm system. | Amended | 07/21/1993 |
SA5924NM | Installation of RPM instrument. | Amended | 06/03/1994 |
SA5925NM | Installation of oil pressure/temperature instrument. | Amended | 06/03/1994 |
SA5926NM | Installation of manifold pressure instrument. | Amended | 08/15/1993 |
SA593CH | Install Unison SlickSTART tm magneto booster system. | Amended | 04/20/2000 |
SA648NE | Installation of Cessna 150 exhaust systems. | Issued | 04/25/1989 |
SA666NW | Installation of Teflon control yoke bushings. | Amended | 05/15/1996 |
SA692GL | Modify airplane to fly on unleaded automotive gasoline, 87 minimum antiknock index. | Amended | 01/04/1988 |
SA69NW | Installation of Matney’s engine charge air-air filter assembly. (AA-1B, AA-1, AA-1A 1969 AND ON) | Amended | 10/08/1974 |
SA71GL | Installation of air filters per AML No. SA71GL latest FAA approved revision on single-engine | Reissued | 06/20/2000 |
SA800EA | Installation of Aviation White Anti-Collision Strobe Lights. Whelen Models A429, A430, A434, A450, | Amended | 09/08/1999 |
SA800NE | Installation of alternator system on Cessna 120, 140, and 140A aircraft with Continental engine | Amended | 11/08/2002 |
SA8075SW | Installation of fiberglass covering. (M-62 SERIES PT-19) (G-73 SCHWEIZER) | Amended | 03/31/1997 |
SA8150SW | Installation of VENTUBE pilot/co-pilot overhead fresh air valves. (195 SERIES LC-126A; LC-126B; LC-126C). | Reissued | 11/13/2000 |
SA86NW | Installation of automatic carburetor alternate air control unit. | Issued | 12/28/1973 |
SA995SW | Increase wing leading edge radius wing tip fairings, and landing light lens. | Reissued | 04/27/1984 |
SA99EA | Installation of Fram lube oil filter Model PB55-1. | Amended | 09/11/1967 |
SA04382CH | Installation of Cessna 150 seats and seat rail supports | Issued | 07/18/2019 |